VrOne
|
ON-LINE REFERENCE DOCUMENTATION CARDINAL SYSTEMS, LLC 386-439-2525 |
Type: Interactive Application
Drives to grid points within a user defined polygon and allows reading of those points as symbols, spot elevations or text elevations. DTM may be run during the read process and the elevation from the DTM surface may be driven to when moving to new grid points.
|
Key-in |
Description |
Range |
|
TYPE= |
Point type to place when reading grid |
0 = Symbol 1 = Spot Elevation 2 = Text only |
|
GRIRES= |
Grid resolution |
Ground units |
|
GRIOFSX= |
Grid offset X |
Ground units |
|
GRIOFSY= |
Grid offset Y |
Ground units |
|
TEXOFSX= |
Text offset X (in|mm) |
Inches | Mm |
|
TEXOFSY= |
Text offset Y (in|mm) |
Inches | Mm |
|
DECACC= |
Decimal accuracy for Z text labels |
|
|
ZCON= |
Z control |
0 = Footdisk 1 = Right handwheel 2 = P3 Y tablet motion |
|
READIR= |
Read direction |
0 = East ascending 1 = East decending 2 = East meander 3 = North ascending 4 = North decending 5 = North meander |
|
DRIGRI= |
Drive Z to DTM surface, if active |
0 = No 1 = Yes |
|
Key-in |
Description |
Range |
|
LAY= |
Layer number |
1-10001 |
|
GRP= |
Graphic pointer |
1-60 |
|
PEN= |
Pen number |
1-256 |
|
CON= |
Construction flag |
0-1 |
|
NGR= |
Non graphic pointer |
32bit |
|
LNK= |
Link number |
32bit |
|
FC= |
Feature code |
48 char |
|
RAD= |
Symbol radius |
Inches | Mm |
|
ROT= |
Symbol rotation |
Degrees |
|
FKEY= |
Set symbol and text parameters to Function Key |
Function key name |
|
Key-in |
Description |
Range |
|
KEY1= |
Layer number |
1-10001 |
|
GRP1= |
Graphic pointer |
1-60 |
|
PEN1= |
Pen number |
1-256 |
|
CON1= |
Construction flag |
0-1 |
|
NGR1= |
Non graphic pointer |
32bit |
|
LNK1= |
Link number |
32bit |
|
FC1= |
Feature code |
48 char |
|
FNT= |
Font number |
1-12 |
|
JX= |
Justification X |
1=Lower 2=Center 3=Upper 4=Decimal |
|
JY= |
Justification Y |
1=Left 2=Center 3=Right |
|
HGT= |
Text height |
Inches | Mm |
|
WDT= |
Text width |
Inches | Mm |
|
ROT1= |
Text rotation |
Degrees |
|
SLT= |
Text slant |
Degrees |
These X,y distances will be added when driving the instruments to the grid points.
Defines location of Z motion. NOTE: Not available on all instruments.
If this parameter is set to yes then the elevation from the DTM surface will be used when driving to a grid point. It is possible to run DTM at any time and strengthen the surface based on previously read grid points. DTM may be run without exiting Drive Grid.
|
Example Scale Factors |
Comment |
|
1.0 |
No scale factor |
|
-1.0 |
Reverse direction of Z motion |
|
-2.5 |
Reverse direction and multiply speed by 2.5 |
|
.5 |
Divide Z motion speed by 2 |
|
|
Button
|
Description |
|
1 |
Id line |
Identify grid area boundary line |
|
2 |
|
|
|
3 |
|
|
|
4 |
|
|
|
5 |
|
|
|
6 |
|
|
|
7 |
Parameters |
Enter grid parameters |
|
8 |
Symbol Params |
Enter symbol parameters |
|
9 |
Text Params |
Enter text parameters |
|
* |
|
|
|
0 |
|
|
|
# |
End |
Ends Drive Grid |
|
|
Button
|
Description |
|
1 |
Accept point |
Reads grid point at current location |
|
2 |
Next point |
Moves to next grid point |
|
3 |
Backup |
Moves to previous grid point |
|
4 |
Drive back |
Drives back to current grid point |
|
5 |
Resume |
Allows Id of grid point to resume reading. |
|
6 |
|
|
|
7 |
|
|
|
8 |
|
|
|
9 |
|
|
|
* |
|
|
|
0 |
|
|
|
# |
End |
Returns to Lock On |